1 place the end of a tape measure against the wall behind the existing toilet, not on the molding at. To do this, the floor must opened up, and if the bathroom is at basement level, this will entail breaking through the concrete.
Brushed Satin Stainless Dishwasher Update As Seen On TV
Installing a toilet over an existing rough in is relatively simple, but relocating one can be tricky and should only be handled by someone with prior plumbing knowledge.
How to measure existing toilet rough in. The closet bolts are the bolts holding your toilet to the floor. If measuring for a replacement toilet, just measure from the back wall to the center of the toilet drain and write down the measurement. If there are four bolt caps, measure to the rear set of bolt caps.
10 inch rough in toilet. You could do this with a vanity cabinet in the store, a door, a nearby wall or post, or you could bring along your 4' level and do it that way. Therefore like people had said, measure from the bolts to the front of the toilet, go look for a 12 rough in toilet, and measure those bolts to the front of the toilet, if its the same, you will not lose any space in the front, you will just close the gap in the back of the toilet by 2.
When you are figuring out your toilet rough in dimensions, you will end up with one of three basic measurements. Compare that measurement to the rough in of your old toilet. On either side of your toilet, youll see two bolts (usually with caps on them).
The flange rim will be fastened to the finished floor later. To do this, take a tape measure and measure from the back wall (not baseboard) to the center of one of the rear closet bolts. Measure from the center of those caps or bolts to the wall and that measurement is your rough in.
The center of the toilet flange should be 12 from the finished wall (add a 1/2 for drywall if measuring from the framing). One common standard toilet flange size is 4x3, and this is the measurement you will find beside most flanges available at your hardware or plumbing stores. Oversize toilets may not fit in this area however.
If your existing toilet has four bolts, measure to the center of the back bolts. Measure toilet rough in with existing toilet. In most north american homes that dimension is either 10, 12, or 14 inches, the most common in todays homes being 12.
Measure the distance between the center of the drainage pipe, or preferably the flange, to the wall. If the toilet is still in place, the center of the flange should align with the rear bolts that keep the toilet attached to the floor. Do not measure from the baseboard, instead, measure from the wall (baseboard will reduce your measurement an inch or so).
Cut a hole in the subfloor just large enough for the bottom part of the toilet flange to sit. If the base of your new toilet is equal to or smaller than your old toilet's rough in, you should have no problems making the new toilet fit. If your existing toilet has four bolts, measure to the center of the back bolts.
The center of the toilet flange aligns with the middle of the toilet bolts that hold the toilet bowl in place. Make sure to measure the distance from the wall (not the skirting board) to the center of the flange. Keep this measurement handy when you go to purchase the replacement toilet.
If your bathroom is compact in size or you live in an older home, theres a good chance that your toilet rough in size will be 10 inches. Measure the distance from the closet bolts to the back of the tank on your desired toilet. If your existing toilet has four bolts, measure to the center of the back bolts.
This is how to measure toilet rough in and toilet dimensions (inches). Most rough openings are 12 inches, but can be as little as 10 inches and as much as 14 inches. Usually, the distance is 12 inches, so a standard toilet will fit just fine in this space.
Are there different size toilet flanges? Measuring rough in on remodeled bathroom; This gives you the length of the base of your new toilet.
As i remodel the bathroom in our condo, i have found that the toilet drain pipe is really close to the wall (the last tenant actually cut into the wall behind the toilet to get the tank to fit) so i was thinking about a corner toilet with a triangular tank. If youre remodeling your bathroom you might have removed the old toilet. Well, with each toilet you put a vertical edge up against the back of the toilet (to simulate a wall), then measure from the bolt holes back to that wall.
Look for a toilet matching the distance. Keep this measurement handy when you go to purchase the replacement toilet.
Escalier doubles limons, marches bois, rampe lisses en
Struggling with your existing toilet? Finding it
Kohler K6488 Whitehaven, 36" Cast Iron Farmhouse Sink
