How To Level Ground For Pool With 2x4

Setting the track on sand. Once the leveling is underway, periodically check your progress by laying a carpenter's level.

Dirt To Deck How Build A Ground Level Floating deck

Take the high spots down!

How to level ground for pool with 2x4. This can be done alone (as shown in the video) or with two people. You must put the legs on solid blocks. Drive a stake into the ground, a nail into the stake, and hook a tape measure to it.

You can check that they are level with each other then all the way around. Touch device users, explore by touch or with swipe gestures. Start skimming off the sand, all the time with the level on top of the 2x4.

This distance is what you enter in the calculator below. The pavers need to be level with the ground so they do not poke your liner. If there is a void, shovel on some more sand.

The pavers should be flush with your leveled ground. The best way to level the pool would be to drain it and start over. Trying to level the pool with it full of water might work, but it could also damage the pool.

Attach strings to stretch between the stakes, a few inches above the ground. Measure the distance in inches that you must raise the end up. When autocomplete results are available use up and down arrows to review and enter to select.

Do the ground first, make sure that's level. Mark an area with a 15' radius and you have a very realistic idea of how large your pool will be. Take the level to your side rails dont eyeball the waterline.

No matter how solid your ground looks the legs are likely to sink into the ground if not set on solid blocks. The purpose of the sand is not to level your pool. You want solid ground under your pool.

Then, place one end of the 2x4 on the high side of your pool site and raise up the other end until it is level. In the photo below, i had to raise the end 4 inches. If it is just a small amount off level you might try digging out a little, or you could just live with it for the summer and fix it in the fall.

You just need to go out into the yard and choose a center point. You liner can stretch and you can have if off level but pool within reason. This area does not need to be perfectly square or rectangular unless you are planning on using sod instead of simply replanting your grass.

Step 1, stake off your area to level. Above grounds with liners that have patterns or tile lines will start to look off level at about the half inch mark as the naked eye can compare the level pool waterline against the pattern of the liner. Under a 24 deck, the ground will need to be covered to prevent weed growth through the decking on such a low deck.

In our part of the world a flat yard is a rare thing. When they come to install the pool take a look at the boxes. Pull the 2x4 toward you so as to fill in the area disturbed where you are kneeling.

Also take into account the way your liner attaches to the pool wall. That will keep them from sinking. This will usually be your starting point and the rest of the ground.

Go to your lowest spot and start your leveling process there by removing all the dirt around the circumference of the pool site plus 1ft so you have room to work. Most above ground installation manuals will say that a pool should be level within an inch, but i try to get it level to an eighth of an inch or so. Yes you do want pavers under your legs.

Drive wooden or plastic stakes around the area to be leveled.step 2, use a string level. When i put my 24fter in i felt i was off as well despite using a buddies survey gear. If you are using sand to level things out you will have nothing but problems.

To level ground for a pool, dig away slopes and high spots to make them level with lower areas. Level the string with a small hanging level. The decking needs to be designed for ground contact or sufficiently raised off the ground to prevent rot.

When you get your pool completely empty, remove the pool from the site. The ground prep is a lot of work but it will pay off in the end! You will have to ensure the beginning, middle, and ends of the 2x4 are all level.

Then measure an even amount down from the string and smooth with a section of 2x4. Sand/dirt can/will shift and move. If there is a great excess, rake the sand.

Once you are level, then you can put the pool frame back into place to see where your pavers will go. The ground should be dug level on virgin soil always. To get it generally level, stretch a string from one side to the other on small stakes.

The sand is simply a buffer from the pool liner to the ground. Click on photo to enlarge. If you have a pool for your kids, you will want it on a flat surface.

Then you can dig down where the legs go to set the pavers flush with the ground. Attach a string level to the strings to determine the high point. Using too much mason sand.

Above ground Pool deck Wolf composite decking Deckorators